www.megger.com 1EVX100EV charger interface for the MFT-X1DESCRIPTIONThe EVX100 is designed as a fully integrated accessory to the MFT-X1 offering an automated test interface for testing singe and three-phase Mode 3 AC electric vehicle charging stations (Mode 3 EVSE chargers).The EVX100 in combination with the MFT-X1 offers the ideal test solution for installation verification and servicing of EV chargers, removing the need for the traditional remotely located manual adaptor/control box.When the EVX is connected to the MFT-X1 the instrument recognises the EVX100 and the MFT automatically offers the operator the necessary EV charger testing options with no need to touch the EVX interface.The EVX100 offers a range of EV charger testing options, all controlled through the MFT-X1 test interface, including single and 3 phase. There is no need for manual controls or additional test leads.PP and CP states are controlled automatically, simplifying the operation of the testing procedures. The MFT-X1 can identify all four operational CP states, A, B, C and D as well as the intermediate state A1, A2, B1, B2 etc. This provides enhanced operational awareness and diagnostic feedback during error conditions.In addition, the EVX will also identify PE issues through the MFT-X1 rather than the manual adaptor touch buttons. This is operated via the dual (ambidextrous) test buttons on the MFT and will inhibit or just warn the user of any issues depend on the MFT configuration.The PE warning function now works via the MFT-X1 when touching the test buttons.The EVX100 is supplied with the Type 2 charging plug. Testing of IEC61851 and IEC62955 protective devices is automated through the EVX. When an RCD trips during an RCD or RDC test the EVX automatically generates an EV charger reset. As soon as power is restored to the charger the EVX resets the charger, removing the need for user to select C-B-A-B-C on the CP knob of a manual adaptor. The EVX will operate with all existing MFT-X1 instruments with the latest free firmware update from the Megger website.The EVX100 is powered by a lithium-Ion battery with USB type C charging port.Achieving IP54, the adaptor meets the same IP standard as its MFT host and enables its use in inclement weather.Leveraging all the test capabilities of the MFT-X1 the combination of EVX100 and MFT-X1 offers an exceptionally simple and flexible solution to electricians working on both the incomer and load side of the EV charging station. Fully integrated to the current MFT-X1 Simple operation Integrated with MFT-X1 control interface Automated EV charger resetting Full EV control by the MFT-X1 CP code reporting IP54 compliance CAT II 250 V rating Carry case included
SALES OFFICE Megger LimitedArchcliffe Road DoverCT17 9EN EnglandT. +44 (0) 1304 502101E. UKsales@megger.comEVX100-DS-EN-V03www.megger.comISO 9001The word ‘Megger’ is a registered trademarkFEATURESEVX100 interfaceOptional accessoryEVX100 interfaceTest leadType 2 plug Type 1 plugCAT II 250V complianceIP rating IP54Rechargeable Li-ION batteryType C charging leadCarry caseQuick start guide Full user guideAvailable onlineSafety warningsSPECIFICATIONSPower supply:Internal battery:Li-ion 3180 mAH Recharging:Type C USB (required supply is 5 V, 1 A maximum)Charging status:LEDInput voltage230 V AC nominalmax 253 V AC400 V AC nominalmax 440 V ACInput frequency:50/60 HzCP state verification:A1, A2, B1, B2, C1, C2, E, FFor measurement specification refer to the MFT-X1 user guide. See megger.com/mft-x1Connection options:Fixed type 2: IEC 62196-1Safety:IEC61010-1:2010 61010-031:2015, CAT II 250 VTemperature range:Working range:-10 °C to +55 °CStorage range:-25 °C to +70 °CHumidity range:90% R.H at +40 °C maxIngress protection:IEC 660529: IP 54: Equipment is protected against ingress of dust and water splashes and is suitable for indoor and outdoor use.Vibration:MIL-PRF-28800F: Class 2Maximum operating altitude:2000 mPollution degree:2MechanicalEVX case dimensions: 133.5 x 115 x 56 mm (5.2 x 4.5 x 2.2 inches) excl. cable.Unpackaged weight:976 gPackaged dimensions:350 x 280 x 75 mm (13.8 x 11.02 x 2.96 inches)Packaged weight:1580 g Cable length:2 mORDERING INFORMATIONDescription Part numberEVX100 1016-183Included accessories Carry case 2017-285User guide 2017-287Optional accessoriesEVX100 carry case 2017-285Type 1 to type 2 adaptor 1014-901EVX100EV charger interface for the MFT-X1
